Insert the handles of your pliers into the section of the drain inside the tub. Spread a pencil-sized bead of putty around the rim of the new flange. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Slide a new gasket into the opening, what is a good then screw in the new flange. Unscrew the exposed drain flange with a drain key or pliers.
How to Install a Tub Drain 10 Steps (with Pictures) - wikiHow
Carefully flip the tub on its side. Let it sit for an hour, then go back and see if any water drained. Keep them in a safe place until you reinstall the drain. The linkage connects the lever to a plunger, which drops down to stop the tub when the lever is down.
How to Install a New Bathtub - dummies
Bathtub Plumbing Installation Drain Diagrams
- If necessary, wipe away any stubborn residue with rubbing alcohol.
- Twist or screw on the new stopper, if necessary.
- Warnings If you notice rusting, mildew, or water pressure problems when you attempt to replace a drain, contact a plumber.
Include your email address to get a message when this question is answered. If in doubt, nick holder no more pull the tub and realign without the tailpieces installed. Sit the tub upright before tightening the screws all the way down. Already answered Not a question Bad question Other.
Apply plumber's putty or silicone caulk to the underside of the top section of the drain and push it into the drain hole on the tub. Place the tub into the installation location and measure these locations again, french dating site but from the inside of the tub. It may take several attempts to get this right. Pull up as you twist it counterclockwise until it lifts out of the drain flange. Thread the linkage through the overflow hole if you have a lever drain.
Wedge another gasket between the overflow ell and the overflow opening on the tub. Tip It is vital that your drain and rough-in line up exactly. Instruct your friend to place the overflow hold down plate into position and hand-fasten it with the provided screws. Take off the overflow plate, and pull the linkage rod and plunger out of the overflow hole. Cookies make wikiHow better.
If your new drain came with a rubber gasket, place it over the drain opening. No matter the reason, bathtubs are added and replaced by homeowners on a regular basis. Take care not to damage the tub's enamel and avoid using harsh, abrasive cleaning products. Turn a foot lock stopper counterclockwise to take it out of the drain.
Measure the exact location of the drain and overflow relative to the tub installation and record the measurements. Kristi Waterworth started her writing career in as a journalist for a local newspaper. You can find drain keys online and at home improvement stores.
7 Bathtub Plumbing Installation Drain Diagrams
Wipe away the excess sealant. Then, using a screwdriver, turn the screw counterclockwise and lift the stopper out of the drain flange. Feed it into the overflow pipe, screw the overflow faceplate onto the opening, then screw the new drain plate onto the flange. Open the access panel that hides the tub drain rough-in. Hold the drain ell in place with one hand.
Start by removing the screws that secure the overflow faceplate. Owners of older homes frequently dream of upgrading their bathtubs. About the Author Kristi Waterworth started her writing career in as a journalist for a local newspaper. You might just want to banish all traces of the decorating schemes of the s, or need to add functionality or ease of cleaning.
It is the most difficult part of the installation. Things You'll Need Screwdriver. Loosen the center screw if you have a lift-and-turn drain. Give them another half turn with the slip-joint pliers. From start to finish, installing a new drain should only take some elbow grease and an hour of your time!
The putty will help create a watertight seal. All you need to do is rotate the stopper, or the part that moves up and down to open and close the drain. Foot lock stoppers are the simplest type of drain mechanism. On a tub drain, it usually goes on top, since a tub drain normally screws down and into a receiver.
After removing the old stopper, take out the old drain flange, or the housing that connects the tub and drain to the pipe below. Add some water to the tub to test the seal. Did this article help you?
Roll out a long, thin strand of plumber's putty about the size and thickness of a pencil. Click here to share your story. Purchase a new drain assembly online or at your local home improvement store.
Lift-and-turn drains and some foot lock drains may have a screw in the center of the stopper that holds it in place. For a lower maintenance option, go with a lift-and-turn stopper. Compare the two figures, high school dropout if they match you are ready to go.
- The drain flange, or drain basket, is the body that connects the tub and stopper to the waste pipe.
- Slide a strong screwdriver between the handles, and use it like a lever to turn the flange counterclockwise.
- Fit the gasket over the portion of the drain that protrudes out of the bottom of the tub, followed immediately by the drain ell.
- The gasket is a rubber ring that helps create a waterproof seal between the flange and waste pipe.
Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Install the stopper and overflow lift rod according to package directions. On most any sink drain, the gasket goes under the sink, since the sink's receiver is screwed against the drain.
If there is no access to the drain from behind or below, and your tub is sitting in its permanent spot, it is best to consult an expert to hook-up your drain. Hooking Up a Bathtub Drain. The most difficult part of installing the tub itself is hooking up the bathtub drain to the rough plumbing. Open the handles as wide as possible to create a handle and tighten the drain clockwise.